Short answer. Starting torque is what it takes to get a stationary bearing moving. Running torque is what it takes to keep it turning. Preload, fit, seals and grease raise both, but they do not raise them equally. So define which one matters to your machine before you try to lower it.
A low-power motor that fails to start cares about starting torque. A motor that runs hot or draws too much current cares about running torque. A servo or scanner cares about how smooth the torque is, not only how large it is.
Starting torque and running torque
| Starting torque | Running torque | |
|---|---|---|
| What it is | Torque to begin rotation from rest | Torque to maintain rotation |
| Main causes | Elastic contact deformation under preload, and lubricant between balls and raceways | Rolling friction, ball-to-cage sliding, and grease being churned |
| Affects | Start-up current, low-power starting, positioning | Heat, power use, rated current, speed |
These definitions follow published torque guidance for miniature and small ball bearings [1][2].
How large is it? A quick estimate
For a rough figure, use a friction coefficient:
M = μ × P × d ÷ 2
M is friction torque (N·mm), P is the equivalent load (N), and d is the bore (mm). Approximate values of μ:
| Bearing type | Approximate μ |
|---|---|
| Deep groove ball bearing | 0.0013 |
| Angular contact ball bearing | 0.0015 |
| Self-aligning ball bearing | 0.0010 |
| Cylindrical roller bearing | 0.0010 |
| Tapered roller bearing | 0.0022 |
Example. A 6204 with P = 1,000 N and d = 20 mm:
M = 0.0013 × 1,000 × 20 ÷ 2 = 13 N·mm
At 1,500 r/min that is about 2 W lost as heat.
This estimate is for loaded, well-lubricated bearings. It leaves out seal drag and grease churning. At light load and high speed those can be the larger part, so the real figure can be much higher than this. For a light-load motor, treat the estimate as a floor and measure the real bearing.
What raises torque
| Factor | Effect on torque | What to watch |
|---|---|---|
| Preload | Higher | Removes play and adds stiffness, so set it for the job. Too much also shortens noise life |
| Radial clearance | Tighter clearance gives higher starting torque | See the data below |
| Tight fit | Higher | Interference takes up clearance. See bearing fits |
| Grease fill quantity | More grease, more running torque | Reducing it only for torque can shorten life |
| Grease position | Running torque can change | Grease bridging from the cage to the raceways causes fluctuation |
| Grease type and viscosity | Higher viscosity, higher torque | Most noticeable when cold or at start-up |
| Low temperature | Higher | The base oil thickens |
| Speed | Generally higher with speed | Choose grease and preload for the speed |
| Contact seals | Higher | Lip friction adds drag. Non-contact seals and shields add less, but protect less |
| Misalignment | Higher | Check shoulder runout and housing alignment |
| Raceway and ball quality | Affects smoothness | Waviness shows up as torque fluctuation |
Clearance and starting torque: published data
One published table for small instrument bearings under a 75 g thrust test load gives:
| Radial play | Maximum starting torque | Source |
|---|---|---|
| Tight, 0.0001″ to 0.0003″ | 1,800 mg·mm | NHBB [2] |
| Normal, 0.0002″ to 0.0005″ | 1,500 mg·mm | NHBB [2] |
| Loose, 0.0005″ to 0.0008″ | 1,400 mg·mm | NHBB [2] |
The same table shows that a heavier test load and a larger bearing give much higher figures. So never compare torque numbers unless the test load and the bearing size match.
Motor problems and where to look first
| Symptom | First things to check | Possible action |
|---|---|---|
| Motor does not reach rated speed | Too much grease, churning grease, tight fit, too much preload | Reduce fill, change to a channeling grease, check seat sizes and preload spring |
| High start-up current | Grease fill and viscosity, preload, fit | Check at the coldest operating temperature, because that is the worst case |
| Speed suddenly fluctuates, then recovers | Grease falling back between balls and raceways | Reduce the fill, or use a channeling grease |
| Current or heat too high when running | Fill quantity, contact seals, clearance after mounting | Compare with a non-contact seal or lighter fill |
| Starts well warm, stalls cold | Base oil viscosity at low temperature | Choose a low-temperature grease |
| Rough, cogging feel at low speed | Raceway marks, contamination, standstill damage | Inspect the raceway. See why a miniature bearing feels rough |
Change one thing at a time, and keep a set of untouched bearings for comparison. Fill, fit and preload interact, and changing all three at once tells you very little.
Lowering torque always costs something
| Change | Benefit | Cost |
|---|---|---|
| Less grease | Lower running torque | Shorter grease life |
| Lower-viscosity grease | Lower torque, better cold start | Thinner film at heat and load |
| Non-contact seal or shield | Less drag | Less protection against water and dust |
| Less preload | Lower torque | Lower stiffness, axial play, possible noise |
| More clearance | Slightly lower starting torque | More play |
| Polyamide cage | Fewer running torque fluctuations in published guidance | Temperature limits |
| Hybrid ceramic balls | Depends on the application, often considered at high speed | Cost |
So write down a torque target along with the life, noise and protection you still need. See bearing grease selection, how fast a sealed bearing can run and hybrid ceramic bearings.
The bearing is often not the main source
One aerospace engineering handbook separates inherent torque from induced torque. Inherent torque comes from the bearing's own geometry, internal design and lubricant. Induced torque comes from load, speed, fit, temperature and contamination in the machine. Under anything other than very light loads and low speeds, it states that induced torque far exceeds inherent torque, by up to 50 times or more [4].
That data is for airframe control bearings, so do not apply the number to a motor. The lesson does carry over, though. A bearing with a good torque figure on the test bench can still be stiff in your assembly, if the seat is out of round or the fit is tight. Test in the assembly as well.
How to write torque into a specification
A number alone cannot be tested. A useful specification states:
- Type: starting torque, running torque, or fluctuation
- Limit and unit, such as N·mm or mN·m
- Test load: axial or radial, and the value
- Speed and direction for running torque
- Temperature during the test
- Lubricant: grease type and fill quantity, or oil
- Run-in before reading, because grease needs time to channel
- Mounting: free bearing, or fitted in the assembly
- Sampling plan for the batch
For more, see how to write a purchase specification for motor bearings. For oscillating and small-angle use, low-speed torque traces show marks and contamination that a single number hides. See our galvo bearing article.
Frequently asked questions
Is starting torque higher than running torque? Often at low speed, but not always. Running torque rises with speed and grease churning, so at high speed it can be higher.
Which unit should I use? N·mm or mN·m for most ball bearings. Small instrument bearing tables sometimes use mg·mm or g·cm. Convert before you compare.
Do 2RS seals add much torque? Contact seals add lip friction, and on small bearings it can be a large share of the total. Compare the actual options at your speed and temperature.
Can I lower torque just by removing grease? Reducing grease can lower running torque, but it can also shorten life. Test both torque and life, and never run a grease-lubricated bearing with no lubricant.
Why does torque fall after a bearing has run for a while? Grease is pushed aside and channels during run-in, which is why a test should state the run-in. Torque also falls as temperature rises.
Sources and data boundary
Directional effects come from the published guidance below. The friction figure is an estimate. Published numbers apply to their own test conditions. Compare bearings using the same test method, and validate in your own assembly.
- MinebeaMitsumi. Torque (Miniature & small ball bearings). product.minebeamitsumi.com
- NHBB. Starting and Running Torque. www.nhbb.com
- NSK. Rolling Bearings catalogue E1103, section 10: friction.
- RBC Bearings. Airframe Control Bearing engineering handbook: torque, shaft and housing fits, low temperature.
- SMB Bearings. A Guide to Bearing Retainers. www.smbbearings.com
Related guides
- Bearing fits: shaft and housing tolerance guide
- Bearing load ratings and L10 life
- High-speed bearing selection
- Why bearings overheat
Ningbo Shuanghua Bearing (NLHB) is a bearing factory in Cixi, China. Tell us your torque limit and test conditions, along with the speed, load and temperature: request a quote.