Short answer. For a ball bearing, L10 = (C/P)³ million revolutions. L10 is the life that 90% of a large group of identical bearings reach or exceed before fatigue starts. It is a statistical value for a population. It does not promise a service life for one bearing, and it does not cover grease, contamination or mounting problems.
Double the load and calculated life falls to one eighth. That single relationship explains most sizing decisions.
What C, C0 and P mean
| Symbol | Name | What it tells you | Where it comes from |
|---|---|---|---|
| C (Cr for radial bearings) | Basic dynamic load rating | The constant load at which the group reaches an L10 of one million revolutions | Bearing table |
| C0 (C0r) | Basic static load rating | The load limit for a stationary or very slow bearing, where permanent marks on the raceway become the concern | Bearing table |
| P | Equivalent dynamic load | One radial load that has the same effect on life as your real radial and axial loads combined | You calculate it |
| P0 | Equivalent static load | The same idea for a stationary bearing | You calculate it |
C is a calculation reference. Do not read it as a working load. A bearing that actually ran at P = C would reach only about one million revolutions.
The two ratings answer different questions. C is about fatigue over many revolutions. C0 is about denting in one event, such as a shock while the machine stands still.
Step 1: find the equivalent load P
If the load is purely radial, P = Fr. With an axial load as well, use:
P = X·Fr + Y·Fa
For a deep groove ball bearing the decision depends on a limit value e:
- If Fa/Fr ≤ e, then X = 1 and Y = 0. The axial load is small enough to ignore, so P = Fr.
- If Fa/Fr > e, then X = 0.56, and Y comes from a table based on Fa/C0.
Example. A 6204 carries Fr = 1,000 N and Fa = 300 N. From our data, C0 = 6,600 N. The table is read from f0·Fa/C0, where f0 is a factor from the bearing table. With f0 = 14, f0·Fa/C0 is about 0.64, which gives e of about 0.25 and Y of about 1.75. Fa/Fr = 0.30, which is above e, so:
P = 0.56 × 1,000 + 1.75 × 300 ≈ 1,085 N
Step 2: calculate L10 and L10h
For ball bearings:
- L10 = (C/P)³, in millions of revolutions
- L10h = L10 × 10⁶ ÷ (60 × n), in hours, where n is speed in r/min
Roller bearings use an exponent of 10/3 in place of 3.
Worked results for a 6204 (C = 12,800 N) at 1,500 r/min:
| Case | P | L10 (million rev) | L10h (hours) |
|---|---|---|---|
| Radial load only | 1,000 N | 2,097 | about 23,300 |
| Radial load doubled | 2,000 N | 262 | about 2,910 |
| With 300 N axial load | about 1,085 N | 1,642 | about 18,200 |
The third row is worth a second look. A 300 N axial load looks small next to 1,000 N radial, yet it takes about a fifth off the calculated life.
You can run your own numbers in the bearing life calculator and the equivalent load calculator.
Going the other way: choose a bearing from a target life
Turn the formula around to find the rating you need:
C required = P × (60 × n × L10h ÷ 10⁶)^(1/3)
Say you need 20,000 hours at 1,500 r/min with P = 1,085 N:
C required = 1,085 × 1,800^(1/3) ≈ 13,200 N
| Bearing | Size (d×D×B, mm) | C (N) | Meets 13,200 N? |
|---|---|---|---|
| 6204 | 20×47×14 | 12,800 | No |
| 6205 | 25×52×15 | 14,000 | Yes |
| 6304 | 20×52×15 | 15,900 | Yes |
The 6304 keeps the 20 mm shaft. The 6205 keeps nearly the same housing envelope but needs a larger shaft. The calculation gives you the required rating. The space in your machine decides which option you take.
Bigger is not automatically better. Oversizing costs money and space, and a bearing running under a very light load can have its own problems, because the balls may skid instead of rolling.
How long should the calculated life be?
There is no single correct number. Bearing makers publish guide values by type of machine. The table below converts one published set of fatigue life factors into hours, using L10h = 500 × fh³.
| How the machine runs | Example machines | Guide L10h (hours) |
|---|---|---|
| Used rarely or for short periods | Small appliance motors, power tools | Up to about 13,500 |
| Used occasionally, reliability matters | Home heater and air conditioner motors, conveyors | About 4,000 to 62,500 |
| Intermittent, for long periods | Small motors, factory motors, machine tools, gearboxes | About 4,000 to 62,500 |
| More than 8 hours a day | Blowers, air conditioning equipment, large motors | About 13,500 to 62,500 |
| Continuous, high reliability | Water supply pumps, power station equipment | 108,000 or more |
Use these as a starting point. Your own warranty period and the cost of a stoppage should move the target.
Reliability above 90%
L10 stops at 90% reliability. For a higher figure, multiply by a reliability factor a1:
| Reliability | 90% | 95% | 96% | 97% | 98% | 99% |
|---|---|---|---|---|---|---|
| Life symbol | L10 | L5 | L4 | L3 | L2 | L1 |
| a1 | 1.00 | 0.64 | 0.55 | 0.47 | 0.37 | 0.25 |
Using our 6204 at P = 1,000 N and 1,500 r/min, 99% reliability gives about 5,830 hours in place of 23,300. The bearing has not changed. You are asking for a much smaller share of failures.
Some older references list 0.62 at 95% and 0.21 at 99%. Those are the values from an earlier edition of the standard. Check which edition your customer specifies.
Machines with several bearings
A machine usually stops when any one bearing fails. So the life of the set is shorter than the life of its weakest bearing. For two bearings that each have an L10h of 20,000 hours, the set works out to about 10,650 hours:
1/L^1.1 = 1/L₁^1.1 + 1/L₂^1.1
Do not skip the static check
Fatigue life tells you nothing about a shock load on a stationary bearing. Check it separately:
fs = C0 / P0
For a deep groove ball bearing, P0 is the larger of Fr and (0.6·Fr + 0.5·Fa).
| Operating condition | Minimum fs for ball bearings |
|---|---|
| Standard operation | 1 |
| Vibration and shock loads | 1.5 |
| Low-noise applications | 2 |
Low-noise motors need the highest margin because even a slight raceway mark can be heard. For our example, P0 = 1,000 N, so fs = 6,600 ÷ 1,000 = 6.6, which is comfortable. A shock during shipping or assembly can still exceed it, and that risk is often overlooked.
When the formula does not apply
- Very heavy load. If P is above C0 or above 0.5C, whichever is smaller, the basic formula is no longer reliable. Ask the bearing maker.
- Oscillating motion. The balls may not leave their own contact area. See our galvo bearing article.
- High temperature. Above about 120 °C, standard rings need dimensional stabilization and the rating may be lower. See high-temperature bearing specification.
- Stainless steel. Ratings differ from chrome steel. Use the actual stainless rating, not the chrome steel figure from a general table. See 440C stainless steel bearings.
Why real life differs from calculated life
Bearings are often replaced for reasons other than fatigue. Published guidance names contamination, wear, misalignment and corrosion as more common causes of field failures [3]. Life also has more than one meaning: noise life, wear life and grease life can all end a bearing's service before fatigue does [1].
A sealed bearing makes this clear. The grease has to last as long as the steel. So read L10h as an upper reference, then check these as well:
- Grease type, fill and operating temperature: bearing grease selection
- Clearance after mounting: C2, CN, C3 and C4 explained
- Shaft and housing fit: bearing fits guide
- Installation and early noise or heat: new bearing noisy or hot after installation
What to send us with an inquiry
A life check needs real operating data. Send what you have:
- Bearing number, or bore, outside diameter and width
- Radial load and axial load, and whether they vary
- Speed, and duty per day
- Operating temperature and environment
- Target life, and what happens if the bearing fails
Frequently asked questions
Does L10 of 20,000 hours mean the bearing lasts 20,000 hours? No. It means 90% of a large group are expected to reach that figure before fatigue starts, under the stated load and speed. Some bearings will last much longer, and up to 10% may fail earlier.
Can I run a bearing at its dynamic load rating C? Not for a normal service life. At P = C the L10 is only one million revolutions. At 1,500 r/min that is about 11 hours.
What does C/P tell me quickly? It is a quick sizing ratio. A C/P of 12.8 gives (12.8)³ or about 2,097 million revolutions. Then convert to hours using your speed.
Is a higher C always better? For fatigue life, yes. But it usually means a larger bearing. Very light loads can cause skidding, and larger bearings cost more and need more room.
Why do two catalogues show different C values for the same size? Internal design and the calculation basis can differ, such as ball size and ball count. Compare the actual rating of the bearing you will buy. Do not assume that the same size means the same rating.
Sources and data boundary
The formulas are general methods from the standards. The worked examples are our own calculations from our published data. They are estimates for comparison, not a guarantee of service life.
- NSK. Rolling Bearings catalogue E1103, sections 4 and 8: bearing life, load ratings, reliability factors, static load factor.
- SKF. Rolling bearings, publication 17000, section B.3: specification life guide values and life adjustment factor a1. www.skf.com
- SKF. Bearings in centrifugal pumps. cdn.skfmediahub.skf.com
- ISO 281, Rolling bearings: Dynamic load ratings and rating life. ISO 76, Rolling bearings: Static load ratings.
Related guides
- Bearing fits: shaft and housing tolerance guide
- Starting and running torque
- 6204 dimensions, load ratings and sourcing
- Why bearings overheat
Ningbo Shuanghua Bearing (NLHB) is a bearing factory in Cixi, China. Send your load, speed and target life, and we will check the bearing size with you before you order samples: request a quote.