NLHB
BEARINGS
TECHNICAL Q&A

Bearing FAQ

The questions buyers and engineers ask us most, in six groups: buying, model codes, ball bearing selection, clearance and preload, grease, and seals. The answers come from situations we meet in everyday quoting and inspection.

1. Buying and ordering

MOQ, lead time, samples and test reports: the four things buyers ask before ordering.

What is the usual minimum order quantity (MOQ)?

For standard deep groove bearings (6200, 6300 series and so on) the MOQ is low, usually from 50–100 pieces. Custom or precision bearings may need 500 pieces or more. For non-standard designs the MOQ is set mainly by tooling and fixture cost. Send us the quantities and we confirm each model.

How long does a quote take?

Standard models are quoted within 1 working day. Non-standard parts need a drawing and process check first, usually 2–3 working days. For urgent requests call +86 574-63197518.

Can I see samples before mass production?

Yes. For critical applications we can send physical samples or measured inspection data first (roundness, roughness, clearance, noise), and you order the batch once they are approved. Standard samples are often free (you pay shipping); custom samples may carry a share of the sampling cost.

What inspection data can come with an order?

Roundness, roughness, dimensions, radial clearance, noise grade (Z and V groups) and hardness, all measured on our own equipment and supplied with the goods. Tell us which parameter matters most in your application and we list it first on the shipping inspection sheet. See Quality & Sourcing.

What is the usual lead time?

Stock series depend on inventory; the fastest ship the same week. Standard models in production usually take 2–4 weeks. Custom designs depend on the structure and batch size; we give a firm date once the drawing is confirmed. We check the real production schedule before quoting a lead time.

2. Model numbers and naming

How to read a code like 6203-2RS C3, and what each prefix and suffix letter means.

What does each part of 6203-2RS C3 mean?

Read it in three parts. 6203 is the basic number (6 = deep groove ball, 2 = dimension series, 03 = bore code, bore = 17 mm). 2RS is the seal suffix (rubber contact seals on both sides). C3 is the clearance group (larger than normal). The full list is in our bearing suffix guide.

How is the bore code worked out? What is the bore of a 6208?

From 04 upward, multiply the two-digit bore code by 5: 08 × 5 = 40 mm, so a 6208 has a 40 mm bore. Codes 00, 01, 02 and 03 are special and mean 10, 12, 15 and 17 mm. Miniature bearings under 10 mm show the bore directly (a 608 has an 8 mm bore).

Are 3200 and 5200 the same bearing?

They are two contact-angle designations for double-row angular contact ball bearings: the 3200 series is about 30° (25° at some makers) and the 5200 series about 35° (marked type A at some makers). Boundary dimensions are the same; the 5200 carries slightly more axial load. Our catalog lists 3200 = 5200 as one model with an alias, and we supply to the designation on your drawing.

Are ZZ, 2Z, 2RS1, DDU and LLU the same thing?

Basically, yes. Metal shields on both sides are written ZZ by some makers and 2Z by others. Rubber contact seals on both sides are written DDU, LLU, 2RS1 or 2RSR by different makers; the generic form is 2RS. This is where cross-brand replacement most often goes wrong. See the suffix guide for the cross-reference.

What do the prefixes F, R, MR and S mean?

F = flanged outer ring (for example F6203, no housing shoulder needed). R = inch series (for example R6, common on imported machines). MR = metric miniature deep groove (for example MR106). S = stainless steel (for example S6203, used by some makers). A few prefixes differ between makers; if unsure, send us the number and we check it.

3. Choosing ball bearings

Deep groove or angular contact? Single or double row? How to balance speed and load.

How do I choose between deep groove and angular contact ball bearings?

Look at the axial load. For pure radial load or very small axial load (motors, fans, pumps), use deep groove. For clear axial force or where axial location accuracy matters (spindles, ball screws, pumps), use angular contact. An open deep groove bearing carries axial load of about 30% of its radial load; angular contact axial capacity rises with contact angle, 15°, 25° and 40°. Neither suits heavy axial shock.

When should I use a double-row angular contact bearing, and when two single-row bearings back to back?

A double-row angular contact bearing (3200/5200 series) is a factory-made pair. It takes axial load in both directions, mounts simply with no preload adjustment and costs less, so most gearboxes, pumps and compressors use it. Two matched single-row bearings (DB/DF) are more flexible: you can choose the contact angle, set preload exactly, and a single row reaches higher speed. Precision spindles use matched pairs; general drives use double-row.

What if the speed is not high enough?

Check three things first. ① Seals: 2RS contact seals run about 40% slower than open or ZZ bearings; for high speed change to ZZ or 2RZ. ② Clearance: use C3 at high speed to allow for temperature difference. ③ Cage: a nylon cage allows one step higher speed than a pressed steel cage. If that is still not enough, go to a higher precision class (P5 or better) or a 15° angular contact bearing. Reference speeds are on our model pages, and you can check the application with the life calculator.

What is the usual bearing set-up for an electric motor?

The most common set-up is a 62-series deep groove bearing with C3 clearance, ZZ or 2RS seals and a noise grade of Z2 or better. C3 is the key for motors: an interference fit on the inner ring and the running temperature difference use up part of the clearance, and C3 keeps the bearing from seizing. Household appliance motors (air conditioners, washing machines) usually require Z3 or better. Most of our motor customers are supplied this way.

4. Clearance and preload

How to choose C2, C3 or C4, and what preload is for.

How do I choose between C2, CN, C3 and C4 clearance?

Clearance depends on two things: the interference fit and the temperature difference. An interference fit expands the inner ring and reduces clearance. In service the inner ring usually runs hotter than the outer ring, which reduces clearance further. Use CN (normal, usually not marked) for ordinary conditions; use C3 for motors and where there is an interference fit or a temperature difference (the most common choice); use C4 for high temperatures (ovens, hot air). Use C2 only for precision, low-noise applications, and confirm that the bearing will not bind after mounting.

What happens if the clearance is too small or too large?

Too small: fast temperature rise, high noise, and in bad cases the bearing seizes on the shaft, which is one common cause of burnt-out motors. Too large: radial play, lost accuracy, more vibration and noise, and shorter life. If a machine runs fine at start-up but gets hot after half an hour, check the clearance group and the fit first.

What is preload, and when is it needed?

Preload is an axial force applied to the bearing at assembly. It removes internal clearance so the balls and raceways stay in contact. It raises stiffness, improves running accuracy and suppresses vibration. It is common on angular contact and spindle bearings. It is set either by position (spacers, springs or nuts) or by constant pressure (springs). Ordinary deep groove bearings are normally not preloaded.

How is clearance measured?

Production lines use feeler gauges (rough) or a radial clearance gauge (accurate). We sample each batch on a dedicated clearance gauge before shipment and can supply the data with the goods. If you measure at incoming inspection, remember that a measurement at room temperature is the clearance before mounting. Working clearance on the shaft is smaller, so do not judge a C3 bearing by comparing a measured value directly with the table.

5. Grease

Which grease, how much, and how often to relubricate.

What grease is in the bearings when they leave the factory?

Sealed bearings (2RS/ZZ) are filled with a general-purpose lithium or lithium complex grease for normal conditions of −30 to 120 °C. For special needs (high or low temperature, food grade, high speed, low noise, low torque), describe the application when you ask for a quote and we fill to a specified grease. Batch orders can specify the grease brand.

How much grease should be filled?

At normal speeds fill 30–50% of the free space inside the bearing. At high speed (above 60% of the reference speed) fill only 20–30%; too much grease churns and heats up. At low speed and heavy load the bearing can be filled. Our sealed bearings are filled to a standard metered quantity; note any special fill rate on the order.

Do 2RS sealed bearings need relubrication?

Sealed bearings are designed to be maintenance-free, and under normal conditions lithium grease usually lasts as long as the bearing. The exceptions are high temperature (continuously above 80 °C), high speed and heavy vibrating loads, where grease ages fast and a regreasing or replacement plan is still needed. Relubricate open and ZZ bearings to suit the application, and purge as much old grease as possible first.

Can different greases be mixed?

Not recommended. Greases with different thickeners (lithium, calcium, polyurea) can change consistency when mixed and may soften and leak out. Use the same grease when relubricating; when changing grease type, clean out the old grease first. This step is often missed in maintenance procedures and is a common cause of early bearing failure.

6. Seals and shields

The practical difference between ZZ and 2RS, and what to use in harsh conditions.

Should I choose ZZ or 2RS?

In short: in a clean environment where speed matters, choose ZZ; in damp or dusty conditions where you want no maintenance, choose 2RS. ZZ is a non-contact metal shield with low friction and high speed, but it does not keep out moisture or fine dust. 2RS is a contact rubber lip seal that keeps out water and dust, at the cost of about 40% lower limiting speed. A detailed comparison, including the 2RZ middle option, is in 608ZZ vs 608-2RS; the principle applies to all sizes.

What is 2RZ, and how does it differ from 2RS?

2RZ is a non-contact rubber seal on both sides: there is a rubber shield, but the lip does not touch the inner ring. Friction is close to ZZ and dust protection is close to 2RS, so it is the compromise when you need both speed and protection. Some makers write it VV or LLB. When unsure, 2RZ is often the safe choice.

What seals suit mud, water and dust, as on farm machinery?

A plain 2RS is not enough. Agricultural bearings use triple-lip seals with a flinger (codes such as 203KRR2): several lips keep out mud, and a metal flinger throws off dirty water. This is the core difference between agricultural unit bearings and ordinary sealed bearings; the outside dimensions may be the same, but the seal design is completely different. See Agricultural bearings.

Can I open a sealed bearing to change the grease?

Technically yes, but it is rarely worth it. Prying out the seal can deform it, the seal works less well afterwards, and the labour cost is high. Standard sealed bearings are designed to be maintenance-free and replaced when worn. Only large, high-value bearings with a specified grease justify an open bearing with manual greasing.

Question not listed? Email [email protected] or call +86 574-63197518. The parameters to prepare before asking for a quote are in What to prepare before you ask for a custom bearing quote.

Inquiry List 0

Your Inquiry List

Submit All as Quote →