Short answer. Choose RAU thin-section crossed-roller bearings when an ultra-short axial pocket must carry heavy overturning moments on one bearing, 3800 / 3900 thin-section double-row angular contact ball bearings when compact wrists or gimbals need lower friction torque and greater housing compliance, and paired 7900 / 7000 (DB) single-row angular contact bearings when shaft length allows separating two bearings for high speed and tunable moment rigidity. NLHB manufactures all three rotary-joint architectures—RAU, 3800 / 3900, and 7900 / 7000—in-house at our Cixi plant.
Robot actuator engineers often switch between these three options during prototyping because each fixes a different constraint: axial width, torque ripple, speed limit, or aluminum housing deflection. For motor-rotor and hollow-cable deep groove positions inside the same joint, see our robot joint thin-section deep groove guide.
Three rotary-joint architectures compared
Line contact (RAU rollers) vs point contact (3800 / 3900 and paired 7900 / 7000 balls) governs friction, speed, and seat sensitivity.
| NLHB in-house architecture | Rolling contact | Axial envelope | Overturning stiffness | Friction torque | Speed ceiling | Seat & bolt sensitivity |
|---|---|---|---|---|---|---|
RAU thin crossed-roller |
90° alternating cylindrical rollers |
Shortest (5 / 8 / 13 mm) |
Highest per unit width | Higher drag; steep rise under heavy preload | Lower | High (2–5 µm shoulder flatness target) |
3800 / 3900 thin double-row |
Two back-to-back ball rows | Compact single ring pair (7–19 mm) |
Moderate (fixed spread) | Significantly lower, less torque ripple | High (11,000–11,500 rpm ref on 25 mm bore) |
Moderate; forgiving in aluminum seats |
Paired 7900 / 7000 (DB/DF) |
Matched single-row ball pair | Longest (2×B + spacer span) |
Scales rapidly with DB span |
Low; tunable preload (L / M) |
Highest (15° C angle / HQ1 ceramic) |
Moderate (spacer parallelism critical) |
1. RAU thin-section crossed-roller bearings: compact moment rigidity
NLHB manufactures 28 catalog sizes in RAU thin-section crossed roller bearings (10–200 mm bore):
- 5 mm wide open (11 sizes, 10–100 mm bore): From RAU1005 (10×21×5 mm, C = 1,120 N, C0 = 800 N, 0.009 kg) to RAU10005 (100×111×5 mm, C = 3,370 N, C0 = 6,630 N).
- 8 mm wide UU sealed (12 sizes, 40–150 mm bore): e.g., RAU4008UU (40×56×8 mm, C = 4,320 N, C0 = 5,650 N) to RAU15008UU.
- 13 mm wide UU sealed (5 sizes, 160–200 mm bore): Up to RAU20013UU (200×226×13 mm, C = 25,800 N, C0 = 54,700 N, 0.71 kg).
Where a harmonic drive uses bolted flanges rather than clamped housings, compare harmonic reducer PRZ vs SF/HF bearings.
The RAU shop trade-off: Thin rings copy the housing behind them. If shoulder flatness exceeds 2–5 µm, or clamping screws are torqued sequentially instead of in a multi-pass cross pattern, the outer ring warps and pinches roller ends—spiking starting torque and ripple. Always verify rotation torque and runout after clamping the housing plate, never only on an unmounted bearing.
2. 3800 / 3900 thin-section double-row angular contact: low torque and wrist compliance
For wrists, gimbals, dexterous hands, and fast actuators hurt by roller drag, 3800 and 3900 thin double-row angular contact bearings place two back-to-back ball rows in one ring pair with factory-set axial play or preload.
Remember that 3800 and 3900 are separate ISO series—not alternate codes:
- Review the 3800 series chart (10–55 mm bore), 3900 series chart (10–55 mm bore), and 30/5–30/8 miniature sizes (5–8 mm bore).
- At 25 mm bore, 3805 is 25×37×10 mm (same d/D as 6805, 3 mm wider) with Cr = 5,500 N, C0r = 4,900 N, and 11,500 rpm reference speed; 3905 is 25×42×13 mm with Cr = 9,600 N, C0r = 7,500 N, and 11,000 rpm reference speed.
- Tight fits in aluminum housings consume internal clearance quickly—pair housing tolerance and operating thermal delta with factory clearance.
3. Paired 7900 / 7000 (DB / DF) single-row angular contact: spaced moment arm
When shaft length permits two separate bearings, paired single-row angular contact bearings (7900 ultra-light and 7000 light) let engineers spread the DB pair with precision spacers to multiply overturning moment stiffness while keeping point-contact speed and low drag.
25 mm bore model |
Dimensions d × D × B (mm) |
Section (D−d)/2 (mm) |
Cr (N) |
C0r (N) |
Engineering fit |
|---|---|---|---|---|---|
3805 (thin double-row) |
25 × 37 × 10 |
6.0 |
5,500 |
4,900 |
Ultra-thin single unit, factory-set play |
3905 (thin double-row) |
25 × 42 × 13 |
8.5 |
9,600 |
7,500 |
Higher capacity in 42 mm OD |
7905 (pair DB/DF) |
25 × 42 × 9 (×2 = 18+) |
8.5 |
7,150 (single) |
4,950 (single) |
Ultra-light 42 mm OD; spread DB for moment arm |
7005 (pair DB/DF) |
25 × 47 × 12 (×2 = 24+) |
11.0 |
10,700 (single) |
6,850 (single) |
High speed (15° C / 25° AC), stiffer DB span |
With DB diverging contact lines, spacing two 7905 or 7005 bearings widens the pressure-center arm, supports 15° (C), 25° (AC), or 40° (B) contact angles plus HQ1 ceramic balls, and lets you tune preload directly. Check combined loads first with our equivalent load calculator.
Selection rules
- Axial space
< 14 mm+ heavy arm moment: SpecifyRAUcrossed-roller, hold2–5 µmshoulder flatness, tighten clamping screws crosswise, and test clamped torque. - Compact wrist, gimbal, or dexterous hand with aluminum housing: Specify
3800 / 3900(or30/5–30/8) withZZshields and an external lip seal. - High-speed servo actuator with room for spacers (
≥ 20 mmspan): Specify paired7900 / 7000 DBwith ground spacers and agreed preload.
Frequently asked questions
Does NLHB manufacture RAU, 3800 / 3900, and 7900 / 7000 bearings in-house?
Yes. NLHB manufactures all three rotary-joint series in-house at our Cixi plant, supporting custom bores, seals, greases, and matched-pair preload agreements.
Why does an RAU bearing bind after bolting into an aluminum housing?
Thin crossed-roller rings conform directly to seat flatness and bolt clamping force. Out-of-flat shoulders or non-cross bolt tightening warps the outer ring and pinches roller ends, raising torque and ripple.
Are 3800 and 3900 interchangeable at the same bore?
No. At 25 mm bore, 3805 is 25×37×10 mm (Cr = 5,500 N) while 3905 is 25×42×13 mm (Cr = 9,600 N). Always verify OD and width limits.
Can a 3805 replace a 6805 deep groove bearing?
Only if the pocket accepts 3 mm extra width. Both share 25 mm bore and 37 mm OD, but 3805 is 10 mm wide compared with 7 mm on 6805.
Why pick paired 7900 / 7000 (DB) over one 3800 double-row bearing?
Separating two DB bearings along the shaft expands the effective moment arm, raises tilting stiffness, and enables custom 15°/25° contact angles and lower drag at high speed.
Sources and data boundary
All RAU, 3800, 3900, 7900, and 7000 dimensions, load ratings, and reference speeds come from NLHB product pages. Housing shoulder flatness numbers carry inline verification tags for confirmation against your joint CAD stack-up.
- NLHB Bearings.
RAUThin-Section Crossed Roller Bearings. https://nlhb.net/products/crossed-roller-bearings.html - NLHB Bearings. Small Double Row Angular Contact Bearings (
30/x,3000,3800,3900). https://nlhb.net/products/3800-3900-thin-double-row-angular-contact-bearings.html - NLHB Bearings. Single Row Angular Contact Ball Bearings (
7000–7900). https://nlhb.net/products/single-row-angular-contact-bearings.html - ISO 76 & ISO 281. Rolling bearings — static and dynamic load ratings and rating life.
Related guides
- RAU thin-section crossed roller bearings
- 30/x, 3000, 3800, 3900 thin double-row bearings
- 3800 series double-row chart
- 3900 series double-row chart
- Single-row 7000–7900 angular contact bearings
- Thin-section bearings for robot joints & servo motors
- Harmonic reducer bearings: PRZ vs SF & HF
- Bearing equivalent load calculator
Ningbo Shuanghua Bearing (NLHB) manufactures RAU, 3800 / 3900, and 7900 / 7000 bearings in-house in Cixi, China. Send your joint loads, envelope limits, housing material, and torque requirements: request a quote.
