Short answer. Choose 4200/4300 double-row deep groove ball bearings when radial capacity is the priority inside a narrower seat than 5200 (4205 is 18 mm wide vs 20.6 mm for 5205). Choose 3200/5200 (or 3300/5300) double-row angular contact bearings when combined radial, bidirectional axial, and overturning moment loads act together, or when 2RS/ZZ seals are required. Never swap a wide 62200 or double-row bearing into a 6200 seat without running a five-step axial envelope and thermal-clearance check.
At a 25 mm bore and 52 mm outside diameter, 6205, 62205-2RS, 4205, and 5205/3205 look like interchangeable relatives. In operation, they represent four distinct internal designs: standard single-row, wide single-row grease shell, vertical-row double deep groove, and back-to-back O-arrangement angular contact.
Side-by-side comparison at 25 mm and 17 mm bores
Matching bore and OD hides major differences in ball count, load rating, and overturning stiffness. The table below summarizes verified NLHB catalog dimensions and ratings at 25 mm (25 × 52 mm) and 17 mm (17 × 40 mm) bores:
| Model | Bearing Type | d × D × B (mm) |
Dynamic Rating C (N) |
Static Rating C0 (N) |
Internal Architecture |
|---|---|---|---|---|---|
6205 |
Single-row deep groove | 25 × 52 × 15 |
14,000 |
7,900 |
1 row; open, ZZ, or 2RS |
62205-2RS |
Wide single-row deep groove | 25 × 52 × 18 |
14,000 |
7,800 |
1 row; wider rings for grease & 2RS seals |
4205 |
Double-row deep groove | 25 × 52 × 18 |
16,300 |
16,900 |
2 rows, no filling slots; two PA66 cages; open dominates |
5205 / 3205 |
Double-row angular contact | 25 × 52 × 20.6 |
19,600 |
15,000 |
2 rows (O arrangement); open, ZZ, or 2RS |
6203 |
Single-row deep groove | 17 × 40 × 12 |
9,600 |
4,800 |
1 row; open, ZZ, or 2RS |
4203 |
Double-row deep groove | 17 × 40 × 16 |
11,700 |
10,400 |
2 rows; radial-heavy double-row deep groove |
5203 |
Double-row angular contact | 17 × 40 × 17.5 |
13,500 |
9,300 |
2 rows (O arrangement); open, ZZ, or 2RS |
Two takeaways stand out immediately:
- Wide
62205-2RS(18 mm) is still a single-row bearing. Its14,000 Ndynamic rating (C) and7,800 Nstatic rating (C0) match standard6205(15 mm). Our 62200 / 62300 wide deep groove catalog uses that extra3 mmfor grease volume and dual seal clearance—not higher fatigue load. 4205pushes static ratingC0to16,900 N(more than double6205), while5205leads dynamic capacity (19,600 N) and moment stiffness. Axially,4205adds3.0 mmover6205whereas5205/3205adds5.6 mm.
Internal architecture: 4200/4300 vs 3200/5200
4200 and 4300 double-row deep groove ball bearings
In the 4200 series and heavy-section 4300 series (from 4300 at 10 × 35 × 17 mm to 4315 at 75 × 160 × 55 mm), both raceways run at 0° nominal contact angle without filling slots. Each ball row takes a snap-in polyamide (PA66) crown cage pressed in from opposite faces.
This geometry delivers high radial static capacity (C0 = 16,900 N on 4205), fitting oil-bath gearboxes and pure radial pump shafts. Two limitations apply:
- Open designs dominate. Fitting two snap-in polyamide cages from both end faces leaves minimal axial land for
ZZshields or2RSseal grooves inside standard4200widths, so open oil-lubricated or externally sealed housings are standard. - Lower overturning moment rigidity and cage temperature limits. With
0°contact angles, moment spread is narrower than5200, andPA66cages impose an upper continuous temperature limit around120 °C.
3200 / 5200 and 3300 / 5300 double-row angular contact bearings
The 3200 / 5200 series and heavier 3300 / 5300 series offset inner and outer groove centers to create a back-to-back (O arrangement) contact angle, commonly 25°–30°. See 3200 vs 5200 designations for why both numbering schemes share the same envelope.
Because contact lines diverge toward the shaft axis, 5205 resists bidirectional axial thrust and cantilevered moments (pulleys, bevel gears) far better than 4205, and readily accommodates open, ZZ, or 2RS closures. Check mixed radial/axial duty with our equivalent load calculator and life calculator.
Five-step check before upgrading a single-row 6200 seat to double-row
Because 6203/4203/5203 and 6205/62205-2RS/4205/5205 share bore and OD, buyers often attempt direct swaps. Never replace a single-row bearing with a double-row bearing without passing all five checks:
| Check Step | What Changes | Dimensional Delta (mm) |
Failure If Ignored |
|---|---|---|---|
| 1. Axial width delta | Overall width B increases |
6203 → 5203: +5.5; 6205 → 4205: +3.0; 6205 → 5205: +5.6 |
Bearing protrudes past housing face |
| 2. Shaft circlip groove & shoulder | Longer inner ring covers step | Inner ring crosses circlip groove edge | Retaining ring cannot seat; inner ring overhangs step |
| 3. Housing bore depth & end cap | Deeper outer ring fills pocket | Outer face hits shoulder or end-cap spigot | Axial binding when end cap is bolted down |
| 4. Shaft oil-seal landing | Wider inner ring shifts outward | Inner face reaches external lip-seal track | Oil-seal lip rides on chamfer and leaks |
| 5. Axial clearance & thermal squeeze | Press fit & warm shaft shrink play | O-rows squeeze tighter under hoop expansion |
Zero axial play, heavy preload, rapid overheating |
Step 5 catches many upgrades off guard. Unlike a floating single-row 6205, a 5205 runs with factory-set axial clearance. Interference shaft fits plus a rotor warmer than the housing shrink that axial clearance directly, so specify axial clearance (C3 or micron band) alongside fits.
Quote checklist for double-row selection or upgrades
Send these five details via request a quote:
- Current bearing & axial space: Existing
62xx/42xx/52xxnumber plus maximum widthBbefore hitting circlips or oil seals. - Load breakdown: Radial
Fr, axialFa(uni- or bidirectional), and overturning moment. - Speed & thermal delta: Operating
rpm, duty cycle, and shaft-to-housing temperature difference. - Closure & cage preference: Open oil bath,
ZZshields, or2RSseals; note oil/ambient temperature above100 °C. - Shaft & housing tolerances: Fit grades so axial clearance can be matched to interference expansion.
Frequently asked questions
Does 62205-2RS carry more load than 6205-2RS?
No. Both use one ball row with essentially identical ratings (C = 14,000 N, C0 = 7,800–7,900 N). The extra 3 mm width in 62205-2RS creates room for grease and rubber seals, not double-row load.
Why does 4205 have a higher static rating (16,900 N) than 5205 (15,000 N) while 5205 has a higher dynamic rating (19,600 N)?
4205 aligns both rows radially (0° angle) for maximum pure radial static distribution. 5205 angles its rows (O arrangement) to carry combined radial, axial, and moment loads dynamically.
Can I order a 4205 with 2RS rubber seals on both sides?
Standard 4200/4300 bearings are mostly open because dual snap-in polyamide cages fill the end-face margin. Choose 5205-2RS / 5205ZZ (20.6 mm wide) when sealed double-row geometry is required.
Can a 4205 drop straight in for a 62205-2RS since both are 25 × 52 × 18 mm?
No. 62205-2RS is sealed and greased for life, whereas standard 4205 is open for oil bath or external seals and demands tighter shaft-to-housing alignment.
What happens if I swap 6205 for 5205 without machining the shaft shoulder?
At 20.6 mm wide (+5.6 mm), 5205 can block the shaft snap-ring groove, interfere with an external oil-seal lip, or prevent housing end-cap closure.
When should I upgrade from 4200/5200 to 4300 or 3300/5300?
When bore is fixed (such as 25 mm) but calculated L10 life or shock exceeds 4205/5205 limits, moving to 3305/5305 (25 × 62 × 25.4 mm) or 4305 (25 × 62 × 24 mm) increases ball size substantially if space permits.
Sources and standards
- ISO 15 / GB/T 276 — Rolling bearings: Radial bearings, boundary dimensions, general plan.
- ISO 281 / GB/T 6391 & ISO 76 / GB/T 4662 — Rolling bearings: Dynamic and static load ratings.
- NLHB Product Catalogs — 4200 Series Double-Row Ball Bearings, 62200 / 62300 Wide Deep Groove Bearings, and 3200 / 5200 Double-Row Angular Contact Bearings.
Related products, tools and guides
- 4200 Series Double-Row Ball Bearings Size Chart
- 4300 Series Heavy Double-Row Ball Bearings Size Chart
- 62200 & 62300 Wide Deep Groove Ball Bearings
- 3200 / 5200 Double-Row Angular Contact Bearings
- 3300 / 5300 Heavy Double-Row Angular Contact Bearings
- Equivalent Dynamic Load Calculator
- Bearing L10 Life Calculator
- 3200 vs 5200 Designation Guide
- Request a Quote or Upgrade Review


